Power Technologies: Jump stakes

Meilissa Lum from Linear Technology, now part of Analog Devices, explains how a low quiescent current diode controller with reverse input protection can be used for automotive power applications
Blocking diodes are widely used in power supplies to solve a variety of problems. In automotive systems, a series diode – pointed from supply to load – protects the downstream module against negative input voltage resulting from accidental reverse battery connection while replacing or jump-starting the battery.
This series diode also helps electronics ride through cold crank conditions, when the battery voltage dips to 4V, by blocking reverse current and holding up the load voltage on reservoir capacitors. Where multiple batteries or a backup supply are available, diodes enable redundancy and graceful power down by paralleling the various supplies in an OR configuration.
While diodes are easy to understand and apply, their forward voltage drop results in significant power dissipation, making them unsuitable in low voltage or high current applications. In low voltage applications, the forward voltage drop becomes a limiting factor for a circuit’s operating range, even when using a Schottky barrier diode. At least 500mV of supply headroom is lost across a series diode – a large degradation in 12V automotive systems, especially when the supply drops to as low as 4V during cold crank.
Since diodes operate at a fixed voltage drop of 400 to 700mV minimum, regardless of current rating, power dissipation becomes an issue in the 1 to 2A range, for surface mount applications. In applications greater than 5A, power dissipation becomes a major issue, requiring elaborate thermal layouts or costly heat sinks to keep the diode and surrounding circuits below their maximum operating temperature.
Heat from the engine exacerbates the thermal design challenge. Bulky heat sinks are an impediment to increasing a car's electronic content or extending its driving range by reducing weight. Automotive circuit designers need a better way.
One answer is to replace diodes with power mosfet switches. The power mosfet is connected so its inherent body diode points in the same direction as the diode it replaces. During forward conduction, the mosfet is turned on, shorting the body diode with a low loss current path through the mosfet channel. When the current reverses, the mosfet is turned off and the body diode blocks the flow of current, thus maintaining the diode behaviour.
The forward drop and power dissipation are reduced by as much as a factor of ten. This forms the basis of an ideal diode, when compared with conventional p-n or Schottky barrier diodes.
An ideal diode controller can drive n-channel mosfets in a wide variety of power supply reverse blocking, ORing and holdup applications. Mosfets with RDS(on) specifications as low as 1mΩ are readily available, so ideal diodes can be built to handle currents in excess of 50A using a single pass device while maintaining voltage and power loss levels ten times better than any diode set-up.
Consider, for example, a low quiescent current controller with an operating range of 4 to 80V. The 4V end of the operating range is particularly important for operating through cold crank conditions, where the diode drop is not tolerable, while the 80V rating allows it to operate and survive high voltage transients in 12, 24 and 48V automotive environments. This can protect downstream circuitry from reverse inputs down to -40V, seen when battery terminals are misconnected.
When operating from a battery, reducing discharge current is important in normal operation and becomes crucial when the load is off. This can be achieved with an operating quiescent current of 155µA, which can be further reduced to 14µA when placed in shutdown mode. Although the mosfet is turned off in shutdown, its body diode can still conduct forward current. Some applications require the ability to turn a load on and off or to control the delivery of power independent of supply voltage. This can be accomplished by driving two n-channel mosfets as a load switch to block forward and reverse current.
How it works
With the n-channel mosfet Q1, the mosfet source is connected to the input supply and acts like the anode of the ideal diode, while the drain is the cathode. When power is first applied, the load current initially flows through the body diode of the mosfet. The controller senses the large forward voltage drop from in to out and drives the mosfet on. The internal amplifier (gate amp) and charge pump try to maintain 30mV forward drop across the mosfet.
If the load current causes more than 30mV of voltage drop, the mosfet is driven fully on, and the forward drop increases according to RDS(on) • ILoad.
If the load current is reduced, the gate amp drives the mosfet gate lower, increasing its on resistance, to maintain a 30mV drop. If the forward current is reduced to a point where 30mV cannot be supported, the gate amp drives the mosfet off. This prevents DC reverse current and allows smooth oscillation-free switchover in redundant power supply applications.
In the event of an input short, the current quickly reverses and is supplied by output capacitance or another supply. The fast pull-down comparator (FPD comp) senses reverse current by measuring the drop across the mosfet between in and out. When there is more than -30mV across the mosfet, the FPD comp comparator responds by pulling the mosfet gate low in less than 500ns.
The /SHDN pin controls the device and the external mosfets. Pulling the /SHDN pin low turns off the external mosfets while reducing device current consumption to a mere 14µA. For turn on, the /SHDN pin can either be left floating or driven high. If left floating, an internal 2.6µA current source pulls up /SHDN.
Better than Schottky
A mosfet based diode layout reduces the power dissipation and forward voltage drop over a Schottky diode, and is more versatile, with a vast selection of mosfets available for virtually any voltage and current combination. At 20A, the 2.8mΩ mosfet dissipates only 1W, saving 8W of power dissipation over the Schottky diode. The mosfet’s greatly reduced forward voltage drop of RDS(on) • ILoad = 56mV, compared with 450mV with the Schottky diode, enables circuits to operate at a lower voltage.
Reverse input protection
A typical 12V, 20A application can handle reverse inputs to -40V. The forward drop is a mere 56mV at full load current due to the mosfet’s low on-resistance of 2.8mΩ.
During input shorts, potentially destructive transients can appear at the in, source and out pins. D1 and D2 protect in and source by clamping the voltage transients to less than -40V. Q1, a 60V BVDSS mosfet with avalanche rating of 50A, absorbs the inductive energy and prevents in, source and out from exceeding their absolute maximum ratings.
Downstream circuitry, such as DC-DC converters and linear regulators require protection against voltages seen by reverse inputs and misconnected battery terminals. The input pins are rated to -40V. To keep the mosfet off, an internal negative comp comparator senses when the source pin is negative with respect to VSS by at least 1.7V, and pulls down on the gate pin. With the mosfet off, the negative voltage is prevented from reaching the load. Reverse input protection is limited to about -40V by the dissipation in R1.
Inrush limited load switch
The device can be used as a switch to control delivery of power to the load. A diode always conducts forward current. In shutdown, it turns off the mosfet, but its body diode still conducts forward current.
To block forward current, an additional mosfet, Q2, is added. The /SHDN pin serves as the control signal to turn on and off the load switch. Pulling /SHDN low turns off both mosfets: Q2 blocks forward current, while Q1 prevents reverse current. The mosfet body diodes point in opposite directions, which blocks forward and reverse current flow. Floating or driving /SHDN high turns on the IC and enables diode behaviour in the mosfets. During turn-on, inrush current can be limited by controlling the slew rate at the gate pin with the gate capacitor, C1, and the controlled gate current.
For multiple power supplies, duplicating Fig. 5 enables active power source selection regardless of relative source voltage. This is in contrast to a passive selection scheme where strict diode behaviour simply selects the input source with the highest voltage supply.
Paralleling supplies
Multiple devices can be used to combine the outputs of two or more supplies for redundancy or for droop sharing. For redundant supplies, the supply with the highest output voltage sources most or all of the load current. If the supply’s output is shorted to ground while delivering load current, the current temporarily reverses, flowing backwards through the mosfet. The device senses this reverse current and activates the fast pull-down comparator (FPD comp) and turns off the mosfet in 500ns.
If the other, initially lower, supply is not delivering any load current at the time of the fault, the output falls until the body diode of its ORing mosfet conducts. Meanwhile, the device charges the mosfet gate with 10µA until the forward drop reduces to 30mV. If this supply is sharing load current at the time of the fault, its associated ORing mosfet simply drives the mosfet gate harder in an effort to maintain a drop of 30mV.
Droop sharing can be accomplished if both power supply output voltages and output impedances are nearly equal. The 30mV regulation technique ensures smooth load sharing between outputs without oscillation. The degree of sharing is a function of mosfet RDS(on), the output impedance of the supplies and their initial output voltages, as prescribed by Ohm’s law.
Extending protection
The diagram shows the device configured as a 48V ideal diode protected against reverse input voltage. R2 is added to extend the Vin to Vout range to -100V DC with the effect of reducing the forward regulation by 10mV. In applications where the output is held up at +48V by a second supply or by charged capacitors, Q1 will block a reversed 48V input supply. In non-redundant applications where the output can be expected to fall to zero when the input supply is removed or accidently reversed, inputs of up to -100V DC are successfully blocked from reaching the output.
R2 is a pulse-rated component so that Vin to Vout transients in excess of -100V are easily tolerated. Q1 was selected for its combination of 250V BVDSS and exceptionally low RDS(on) of 20mΩ, but its avalanche rating is a modest 320mJ with 47A maximum avalanche current.
In the event the reverse current exceeds the mosfet avalanche current rating, D6 can be added to protect Q1 by absorbing any avalanche energy, and this limits the peak Vin to Vout voltage to -150V. Beyond this point, D6 breaks down and passes transient current pulses through to the output.
Conclusion
The ideal diode controller can replace Schottky diodes and function as a load switch. At currents of 1 to 2A or more, the device is superior to a Schottky diode. With its wide 4 to 80V operating range and reverse input capability, the device maintains low forward drop through automotive cold crank and protects the load from reverse battery connections.
Shutdown mode further reduces the already low quiescent current of 155µA down to 14µA and can be used as an on-off control signal for a load switch. All of these capabilities make it suitable for automotive power supply applications.
Meilissa Lum is a design engineer for mixed signal products at Linear Technology, now part of Analog Devices
