Power technologies: Knowing when to stop

Bruce Haug explains how to power automotive start-stop electronic systems
Many car makers have devised a clever way of saving fuel in vehicles by using a concept called a start-stop system. This automatically switches off the engine when the car is at a standstill and in neutral, then restarts it as soon as the driver presses the clutch pedal again.
The auto start-stop function helps reduce both fuel consumption and emissions by turning off the engine each time the vehicle comes to a complete stop, such as at traffic lights, and restarts it again automatically. The reduction in fuel consumption can be as much as 8% in city traffic compared with a car without such a system. This has the added benefit of reducing its carbon dioxide footprint.
The principle is simple, if the engine is not running, it does not consume fuel. The start-stop function turns off the engine whenever it is not needed. In a traffic jam or even in stop-and-go traffic, simply putting the car into neutral and taking the foot from the clutch will activate the function. A start-stop message on the display will signal that the engine has been turned off. To start the engine again, depress the clutch, put the car back into gear and the engine immediately springs back to life ready to drive on without delay.
Driving comfort and safety are not affected by the function. It is not activated, for example, until the engine has reached an ideal running temperature. The same applies if the air conditioner has not yet brought the cabin to the desired temperature, if the battery is not adequately charged or if the driver moves the steering wheel.
The function is coordinated by a central control unit that monitors data from all relevant sensors, including the starter motor and the alternator. If necessary for comfort or safety, the control unit will automatically restart the engine. For example, if the vehicle begins to roll, the battery charge falls too low or condensation forms on the windscreen. Furthermore, most systems recognise the difference between a temporary stop and the end of the trip. It will not restart the engine if the driver's seatbelt is undone, or if the door or trunk is open. If desired, the function can be completely deactivated with the press of a button.
However, when the engine restarts and there is an infotainment system on or any other electronic device requiring greater than 5V, there is a possibility that the 12V battery can dip to below 5V causing these systems to reset. Some infotainment systems operate from a 5 and 8.5V input fed from a step-down converter operating from the car battery. When the input voltage dips below 5V during an engine restart (cold crank), these systems will reset when the DC-DC converter only has the capability to step down the input voltage. Obviously, it is not acceptable to be watching a video or listening to a CD and have them automatically reset every time the car restarts.
DC-DC controller
Fortunately, triple output DC-DC controllers exist that combines a synchronous boost controller and two synchronous step-down controllers in a single package. The synchronous boost converter output feeds the step-down converters to maintain a high enough voltage to prevent electronic systems requiring greater than 4V to reset during an engine restart. In addition, when the input voltage from the car battery to the boost converter is higher than its programmed output voltage, it runs at 100% duty cycle and simply passes the input voltage directly to the step-down converters, reducing power loss.
The diagram shows a schematic with the synchronous boost converter supplying 10V to the synchronous step-down converters when the battery voltage drops below 10V. In addition to powering the two step-down converters, which produce 5V/5A and 8.5V/3A in this example, the boost converter can be used as a third output that can provide an additional 2A output.
Such a low quiescent current, current mode control, triple-output synchronous DC-DC controller can operate with all n-channel mosfets from input voltages ranging from 4.5 to 38V during start-up and down to 2.5V after start-up. The two buck controllers, channels one and two, operate 180˚ out of phase and can produce output voltages from 0.8 to 24V that are suitable for navigation, infotainment systems, processors and memory. The boost controller, channel three, operates in phase with channel one and can produce output voltages up to 60V. The fixed operating frequency can be programmed from 50 to 900kHz or can be synchronised to an external clock over a 75 to 850kHz range.
Battery run times
Any battery powered system that requires an always-on power bus while the rest of the system is turned off must conserve battery energy. This state is commonly referred to as sleep, standby or idle mode and requires these systems to have very low quiescent current. The need for low quiescent current to conserve battery energy is especially important in automotive applications that can have several electrical circuits such telematics, CD and DVD players, remote keyless entry, and multiple always-on bus lines. The collective current consumption of these systems during standby mode needs to be as low as possible and the pressure continues to mount for battery energy conservation as cars become more dependent on electronic systems for their operation.
DC-DC controllers as discussed here draws as little as 28µA when in sleep mode with the boost converter and one of the buck converters on. With all three channels on and in sleep mode, they can draw down to 38µA, which significantly extends battery run times when in idle mode. This is done by configuring the part to enter high efficiency burst mode operation, where it delivers short bursts of current to the output capacitor followed by a sleep period where the output power is delivered to the load by the output capacitor only.
Load dump
Load dump is a term that refers to the inductive kick that happens after the starter motor is turned off. This surge voltage is normally clamped to 36V maximum for a 12V lead acid automotive type battery system. This surge requires the controller, mosfets and associated components being capable of operating at the clamped voltage. Based on the circuit in Fig. 1, the efficiency is above 92% at full load for each rail.
Protection features
These devices can be configured to sense the output current by using DCR (inductor resistance) or a sense resistor. The choice between the two current sensing schemes is largely a trade-off between cost, power consumption and accuracy. DCR sensing is becoming popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications.
On-board comparators monitor the buck output voltage and signal an overvoltage condition when the output is greater than 10% of its nominal output voltage. When this condition is sensed, the top mosfet is turned off and the bottom mosfet is turned on until the overvoltage condition is cleared. The bottom mosfet remains on continuously for as long as the overvoltage condition persists. If the output voltage returns to a safe level, normal operation automatically resumes.
Conclusion
Automotive start-stop systems allow for fuel savings that will continue to evolve over the next several years. Care must be taken with regards to powering on-board infotainment and navigation systems that need up to, or can exceed, 5V for correct operation. These systems can reset when the input voltage drops out of regulation with an engine restart.
But devices exist that boost the battery voltage to a safe operating level with an on-board synchronous boost controller. Combined with two synchronous step-down controllers, suitable for powering many automotive electronic devices, these devices maintain regulation for all output voltages during an engine restart.
Bruce Haug is senior product marketing engineer for Linear Technology
