Power Technologies: Heavy Loads

Schematic of switching regulator controller with 4.5 to 60V input to 8.5V, 3A and 3.3V, 5A outputs

Bruce Haug from Linear Technology explains why robust power conversion is a must have for lorries, automotive and heavy equipment

 

 

Lorry, automotive and heavy equipment environments are very demanding for any type of power conversion devices. Wide operating voltage ranges coupled with large transients and wide temperature excursions combine to make reliable electronic system design challenging.

To complicate design considerations further, some applications require the power conversion device be installed under the bonnet, requiring a high temperature rating. At the same time, as the number of electronic components is increasing, space requirements are continuing to shrink, making high efficiency conversion critical due to space limitations.

Consequently, reliable lorry switching DC-DC regulators need to work over a wide input voltage range. A 60V input rating gives good margin for a nominal 12V system, which is usually clamped in the 36 to 40V range. Double battery applications, commonly found in both lorries and heavy equipment environments, require an even higher operating voltage due to their nominal 24V battery voltage. Most of these are clamped to 58V, so a 60V rating is usually sufficient.

The on-board automotive and lorry overvoltage clamp is required to maintain a maximum transient voltage caused by the inductive kick back voltage from the starter motor, which can cause a much higher transient voltage when left unclamped.

There are several electronic systems that require continuous power even when the vehicle’s motor is not running, such as remote keyless entry, GPS and security systems. It is essential for these types of always-on systems to have a DC-DC converter with low quiescent current to increase the battery run time when in sleep mode. Under such circumstances, the regulator runs in normal continuous switching mode until the output current drops below a predetermined threshold of around 30 to 50mA.

Below this level, the switching regulator must go into lower quiescent current operation to reduce the current draw to tens of micro amps, thereby lowering the power drawn from the battery, which in turn extends the battery run time.

With 60V input capable DC-DC converters that have high step-down ratios in short supply, designers have resorted to a transformer-based topology or external high side drivers to operate up to 60V. Others have used an intermediate bus converter, requiring an additional power stage.

Both of these alternatives increase the design complexity and, in most cases, reduce the overall efficiency. However, there are 60V input capable step-down switching regulator controllers that address many of the key issues required in automotive and lorry applications. The diagram shows such a device operating in an application that converts a 4.5 to 60V input into 3.5V, 5A and 8.5V, 3A outputs.

These high-voltage dual-output synchronous step-down DC-DC controllers draw only 29µA when one output is active and 34µA when both outputs are enabled, and are in regulation. The 4.5 to 60V input supply range protects against high-voltage transients, ensuring continuous operation during automotive cold crank, load dump and to accommodate a broad range of input sources and battery chemistries. Each output can be set from 0.8V to 99 per cent of Vin at output currents over 20A with efficiencies as high as 96 per cent, making them well suited to 12 or 24V automotive, lorry and heavy equipment applications.

Such devices can operate with a selectable fixed frequency between 50 and 900kHz, and can be synchronised to an external clock from 7 to 850kHz. The user can select from continuous operation, pulse-skipping and low ripple burst mode operation during light loads. Two-phase operation reduces input filtering and capacitance requirements. A current mode architecture provides easy loop compensation, fast transient response, fixed frequency operation, line regulation and easy current sharing with paralleled phases for higher current. Output current sensing is accomplished by measuring the voltage drop across the output inductor (DCR) for the highest efficiency or by using an optional sense resistor for high accuracy.

 

Burst mode

When configured for burst mode operation and during a light load condition, the converter will burst out a few pulses to maintain the charge voltage on the output capacitor. It then turns off the converter and goes into sleep mode with most of its internal circuits shut down.

The output capacitor supplies the load current and, when the voltage across the output capacitor drops to a programmed level, the converter starts back up delivering more current to replenish the charge voltage.

The action of shutting down and turning off most of its internal circuits significantly reduces quiescent current, thereby helping to extend the battery run-time in an always-on system when the system is not running.

The burst mode output ripple is load independent so only the length of the sleep intervals will change. In sleep mode, much of the internal circuitry is turned off except for the critical circuitry needed to respond quickly, further reducing its quiescent current. When the output voltage drops low enough, the sleep signal goes low and the controller resumes normal burst mode operation by turning on the top external mosfet.

Alternatively, there are instances when the user will want to operate in forced continuous or constant frequency pulse skipping mode at light load currents. Both these modes are easily configurable but will have a higher quiescent current and a lower peak-to-peak output ripple.

Furthermore, in forced continuous operation or when clocked by an external clock source, the inductor current is allowed to reverse at light loads or under large transient conditions. Continuous operation has the advantage of lower output voltage ripple but results in a higher quiescent current.

 

Features

Each channel has an overvoltage comparator that guards against transient overshoots as well as other more serious conditions that may overvoltage the output. When the VFB1, 2 pin on Fig. 1 rises by more than ten per cent above its regulation point of 0.800V, the top mosfet is turned off and the bottom mosfet is turned on until the overvoltage condition is cleared.

Fast accurate over current limit protection is essential in a high-voltage power supply. When the output voltage falls to less than 70 per cent of its nominal level, foldback current limiting is activated, progressively lowering the peak current limit in proportion to the severity of the overcurrent or short-circuit condition.

Using 1.1Ω on-board n-channel mosfet gate drivers reduces transition times and switching losses. The gate drive voltage can be programmed from 5 to 10V to allow the use of logic- or standard-level n-channel mosfets to increase efficiency. Due to the high drive current available, multiple mosfets in parallel can be driven for higher current applications.

The 8.5V output produces a very high efficiency at up to 98 per cent. The 3.3V is also over 90 per cent efficient. In addition, this design is still over 75 per cent efficient for each output with a 1mA load. This is due to its burst mode operation.

 

Fast transient response

A fast 25MHz bandwidth operation amplifier can be used for voltage feedback. The high bandwidth of the amplifier, along with high switching frequencies and low value inductors, allow for a very high gain crossover frequency. This lets the compensation network be optimised for a very fast load transient response.

 

Conclusion

Such devices as described here bring a new level of performance in terms of needing to operate safely and efficiently in a demanding high-voltage transient environment. The powerful adjustable gate drive voltage provides the flexibility of driving logic- or standard-level mosfets. Their low quiescent current preserves battery energy during sleep mode allowing for increased battery run-time, a very useful feature in always-on bus systems. The 60V maximum input voltage, fast transient and high temperature grades make them an excellent choice for lorry, heavy equipment and automotive applications. As a result, system designers now have an optimum choice for their DC-DC conversion needs.

 

Bruce Haug is senior product marketing engineer for Linear Technology

 

www.linear.com

Recommend to Colleagues: