Test & Measurement: Fork on the road

Typical screen display from the Yokogawa WT1800 precision power analyser used for testing the Karabag 500E electric car

Test instruments are playing a key part in the joint development of a family of cost-effective electric vehicles

Fork-lift truck manufacturer Linde Material Handling of Aschaffenburg and Karabag based in Hamburg have converted a conventional Fiat 500 into an electric car. The Karabag 500E is a conventional Fiat 500 retrofitted with an electric drive. The vehicle has a three-phase asynchronous motor, providing 20kW of nominal power, and a 125V 11kW lithium polymer battery. It can reach a top speed of 105km/h with a range of 100km.

The conversion components come from a Linde forklift with appropriate modifications. Linde develops and manufactures the electronics and motors for all its vehicles, producing around 50,000 inverters and 400,000 electric motors per year, and is the market leader in Europe in its performance class.

Karabag was searching for a partner to convert a conventionally powered car into an electric vehicle and approached Linde at the end of 2010. Being a Fiat dealer, Karabag had already been offered a way to do this by an Italian supplier, but this was found to be too expensive. The first conversion was done very pragmatically. Linde simply tried most things and changed as little as possible on the car. After four days, the prototype was running. It was able to use existing forklift components such as the motor, inverter, controller, fuse and charging circuits, and basically left them unchanged.

Next, came the definition of driving behaviour, the risk analysis, EMC testing and manufacturer’s declaration. After nine months the project was complete.

To reduce the cost drastically, the battery capacity was halved. Despite the small (11kWh) battery, the range was only reduced from 140 to 100km. With the optimal balancing of the motor, inverter and controller, losses could be reduced, and moreover the driving behaviour is now many times better than before. Compared with the previous conversion kit, Linde was able to dispense with the complete cooling system. In addition, the current setup is smaller and lighter. The electronics fit into a single box, and can be easily replaced if necessary.

 

Testing

For testing purposes, a Yokogawa DL850V Scopecorder and a WT1800 power analyser were connected to the electric vehicle.

The Scopecorder combines a high-speed oscilloscope with a traditional data-acquisition recorder in a single, portable instrument. The power analyser also incorporates a Can bus monitoring function, making it suitable for troubleshooting and debugging the Can in-vehicle serial bus.

Using the analyser, an engineer can decode the Can signal and retrieve information on physical data such as engine temperature, wheel speed and braking from the Can bus signal and compare this with the data coming from real sensors. The result is a great deal of time saved compared with other approaches such as analysis on a PC or using other software.

The instrument has sampling rates as high as 100MS/s, 16bit resolution and input channel isolation providing a withstand voltage up to 1kV. By direct storage of the data on its internal hard drive, longer duration recording is possible. In the Linde application, it was used to monitor the starting (inrush) currents and voltages of the three phases of the motor. For voltage measurements, a 100MS/s plug-in module was used. The three voltages can be directly connected using standard measuring cables, with current transformers being used for current measurement. In parallel, the transmitted Canbus payload is recorded.

Using the manufacturer-specific Can DBC files, the status of various vehicle functions is extracted from the Canbus messages and viewed. This data can be shown as waveforms or as a multimeter display. The queried vehicle functions include direction indicators, lights, parking brake, doors, charging status, battery temperature, battery voltage and battery current.

The power analyser can perform up to six power input measurements, which makes it possible to perform efficiency tests between the input and output of the inverters. The high-resolution 21.3cm XGA display can show up to 12 different pages of measurement items in formats such as numeric, waveforms and trends. A vector display is available for voltage and current phase analysis.

For motor testing applications, the analyser has a motor evaluation function that provides, in a single unit, measurements of all the relevant electrical power parameters along with rotational speed, torque, mechanical power, synchronous speed, slip, motor efficiency and total system efficiency. 

Harmonic analysis can be carried out up to the 500th order from a 50 or 60Hz fundamental frequency. This facility is important for measurements on new power conversion and power electronics devices.

An industry first dual harmonic measurement function makes it possible to measure simultaneously the harmonic content and perform harmonic analysis on two different sources, such as the input and output of an inverter, variable-speed motor drive, lighting ballast, uninterruptible power supply or similar devices. The normal power parameters and harmonic data are measured simultaneously, providing for faster and more accurate power analysis.

An event trigger function is incorporated to capture only a particular event. A trigger can be set for measured values that fall out of a pre-selected range, and the analyser will only store, print or save data that meet the trigger condition.

Currents up to 50A RMS and voltages up to 1000V RMS can be measured directly. Current transformers are required for higher currents.

A wide range of options for representing the measured values on the display is available. The picture shows a display of typical current and voltage waveforms from the inverter in the new electric car.

 

Future

Karabag’s future strategy includes using similar technology in a large van aimed at the market for delivery vehicles in city centres and for shorter distances such as those involved in site traffic for large companies – where reduced costs, lower noise levels and the absence of emissions are key considerations. The company would also like to offer conversion kits for small workshops. These will be preassembled and will contain all the necessary parts. It just needs the battery to be procured, mechanical adjustments to be made and the TÜV authorisation to be carried out.

www.yokogawa.com

Recommend to Colleagues: